BACKPORT: MIPS: Loongson64: dts: fix phy-related definition of LS7A GMAC #21
+4
−2
Conversation
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Currently the LS7A GMAC device tree node lacks a proper phy-handle property pointing to the PHY node. In addition, the phy-mode property specifies "rgmii" without any internal delay information, which means the board trace needs to add 2ns delay to the RGMII data lines; but that isn't known to happen on any Loongson board. The ACPI-based initialization codepath, which is used on LoongArch-based 3A5000 + 7A1000 hardwares, specifies "rgmii-id" phy mode, which should be the one we are using. Add the lacking phy-handle property and set proper phy-mode. Tested on a LS3A4000_7A1000_NUC_BOARD_V2.1 board with YT8521S PHY. Signed-off-by: Icenowy Zheng <zhengxingda@iscas.ac.cn> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Icenowy
force-pushed
the
aosc-6.18-pick-mips-ls7a-gmac-dt-fix
branch
from
cecfc7e to
5d42bda
Compare
Icenowy
changed the title
|
Picked to aosc/v6.18.8, thanks! |
MingcongBai
pushed a commit
that referenced
this pull request
Feb 2, 2026
Fix a use-after-free which happens due to enslave failure after the new slave has been added to the array. Since the new slave can be used for Tx immediately, we can use it after it has been freed by the enslave error cleanup path which frees the allocated slave memory. Slave update array is supposed to be called last when further enslave failures are not expected. Move it after xdp setup to avoid any problems. It is very easy to reproduce the problem with a simple xdp_pass prog: ip l add bond1 type bond mode balance-xor ip l set bond1 up ip l set dev bond1 xdp object xdp_pass.o sec xdp_pass ip l add dumdum type dummy Then run in parallel: while :; do ip l set dumdum master bond1 1>/dev/null 2>&1; done; mausezahn bond1 -a own -b rand -A rand -B 1.1.1.1 -c 0 -t tcp "dp=1-1023, flags=syn" The crash happens almost immediately: [ 605.602850] Oops: general protection fault, probably for non-canonical address 0xe0e6fc2460000137: 0000 [#1] SMP KASAN NOPTI [ 605.602916] KASAN: maybe wild-memory-access in range [0x07380123000009b8-0x07380123000009bf] [ 605.602946] CPU: 0 UID: 0 PID: 2445 Comm: mausezahn Kdump: loaded Tainted: G B 6.19.0-rc6+ #21 PREEMPT(voluntary) [ 605.602979] Tainted: [B]=BAD_PAGE [ 605.602998] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 605.603032] RIP: 0010:netdev_core_pick_tx+0xcd/0x210 [ 605.603063] Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 3e 01 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b 6b 08 49 8d 7d 30 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 25 01 00 00 49 8b 45 30 4c 89 e2 48 89 ee 48 89 [ 605.603111] RSP: 0018:ffff88817b9af348 EFLAGS: 00010213 [ 605.603145] RAX: dffffc0000000000 RBX: ffff88817d28b420 RCX: 0000000000000000 [ 605.603172] RDX: 00e7002460000137 RSI: 0000000000000008 RDI: 07380123000009be [ 605.603199] RBP: ffff88817b541a00 R08: 0000000000000001 R09: fffffbfff3ed8c0c [ 605.603226] R10: ffffffff9f6c6067 R11: 0000000000000001 R12: 0000000000000000 [ 605.603253] R13: 073801230000098e R14: ffff88817d28b448 R15: ffff88817b541a84 [ 605.603286] FS: 00007f6570ef67c0(0000) GS:ffff888221dfa000(0000) knlGS:0000000000000000 [ 605.603319] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 605.603343] CR2: 00007f65712fae40 CR3: 000000011371b000 CR4: 0000000000350ef0 [ 605.603373] Call Trace: [ 605.603392] <TASK> [ 605.603410] __dev_queue_xmit+0x448/0x32a0 [ 605.603434] ? __pfx_vprintk_emit+0x10/0x10 [ 605.603461] ? __pfx_vprintk_emit+0x10/0x10 [ 605.603484] ? __pfx___dev_queue_xmit+0x10/0x10 [ 605.603507] ? bond_start_xmit+0xbfb/0xc20 [bonding] [ 605.603546] ? _printk+0xcb/0x100 [ 605.603566] ? __pfx__printk+0x10/0x10 [ 605.603589] ? bond_start_xmit+0xbfb/0xc20 [bonding] [ 605.603627] ? add_taint+0x5e/0x70 [ 605.603648] ? add_taint+0x2a/0x70 [ 605.603670] ? end_report.cold+0x51/0x75 [ 605.603693] ? bond_start_xmit+0xbfb/0xc20 [bonding] [ 605.603731] bond_start_xmit+0x623/0xc20 [bonding] Fixes: 9e2ee5c ("net, bonding: Add XDP support to the bonding driver") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reported-by: Chen Zhen <chenzhen126@huawei.com> Closes: https://lore.kernel.org/netdev/fae17c21-4940-5605-85b2-1d5e17342358@huawei.com/ CC: Jussi Maki <joamaki@gmail.com> CC: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://patch.msgid.link/20260123120659.571187-1-razor@blackwall.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
2 participants
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Currently the LS7A GMAC device tree node lacks a proper phy-handle property pointing to the PHY node.
In addition, the phy-mode property specifies "rgmii" without any internal delay information, which means the board trace needs to add 2ns delay to the RGMII data lines; but that isn't known to happen on any Loongson board. The ACPI-based initialization codepath, which is used on LoongArch-based 3A5000 + 7A1000 hardwares, specifies "rgmii-id" phy mode, which should be the one we are using.
Add the lacking phy-handle property and set proper phy-mode.
Tested on a LS3A4000_7A1000_NUC_BOARD_V2.1 board with YT8521S PHY.
Reviewed-by: Jiaxun Yang jiaxun.yang@flygoat.com